Brookfield R/S CPS Rheometer Manual de usuario Pagina 34
- Pagina / 62
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
BrookeldEngineeringLabs.,Inc. Page34 ManualNo.M08-218-B0212
The rst user dened value ( = the rst measuring point) is always the start value of the
ramp. The last measuring point is determined as the end value of the user dened value
range. As in our example, to reach the values D = 10, 20, 30, ... , 100 [s
-1
] a starting value
of 10 [
s-1
] is used with increments of 10, therefore, 10 measuring points is required. To
check: 100-10/(10-1) = 10.
Number of Measurement Points = ((End Value - Start Value)/Pre-set Value - 1)
After selection of the menu level “Edit Program”, the user will be prompted to select the
program.
Select program
1) Prog xyz
2) Test
3) NEW
Available programs
contain a name
All free (non-dened)
programs are marked NEW
All free programs are initially marked as NEW. To avoid overwriting existing programs,
select NEW as a program to be edited and select a measuring system. After the selection of
the program with the
OK
key, you will be requested to select a measuring system.
Attention: Any dened program MUST ALWAYS be executed with the same measuring
system, otherwise improper results will be calculated.
Select Meas. system:
1) C25-1/30 >
2) C25-2/30
3) C50-1/30 >
After selecting the measurement system, enter the number of steps (number of ramp and
straight line functions). The number of steps can range from 1 to a maximum of 10 steps.
In this example, we need three steps, so the number “01” is changed to “03” - (see Section
VI.4: Input of Numerical Values and Alphnumeric Texts). The message “Range error” will
appear if <1 or >10 is entered.
Nr of steps: 03
Input number of
steps 1 - 10. This
example is 03.
After entering the number of steps, input the type of measurement.
Select Input:
-D[1/s]
-n[rpm]
-Tau[Pa] >
- BROOKFIELD RS-CPS+ RHEOMETER 1
- Operating Instructions 1
- Manual No. M08-218-B0212 1
- Table of Contents 3
- I.1 Use of the Rheometer 5
- I.2 MeasuringPrinciple 5
- II.1 R/S-CPS+ Rheometer 6
- R/S-CPS+Rheometer 7
- II.2 MeasuringDevices 8
- II.3 ComputerSystem 8
- III.2 Electrical Connections 9
- III.2.1 TemperatureSensor 10
- III.2.2 AC Adapter 10
- III.2.3 Printer Connection 10
- III.2.4 ComputerConnection 11
- IV.3 Cleaning 14
- IV.1 OperatingEnvironment 14
- IV.2 Handling 14
- IV.4 Maintenance 15
- MicrometerRing 17
- VI.1 Keyboard 20
- MAIN-Menu 23
- Thermostat 23
- -Single Measurement 23
- -Program Measurement > 23
- VI.3 SelectingfromLists 23
- Measurment 29
- Automatic increment at 29
- VI.5.4 MAINMenu→ Remote 31
- Wait for RS232 31
- VI.5.5 MAINMenu→ Utilities 31
- D[1/s]=f(t) 33
- Input program name: 36
- (2) TEST 36
- <OK>=Storing 36
- Date of Measurement 38
- Meas. Series Counter 38
- MEASCOUNT 38
- Time of Measurement 38
- Parameters to Set 42
- Stopbits [Bit] 1 or 2 42
- Databits [Bit] 7 or 8 42
- RS232: 19200,8,n,1 43
- <OK>=storing 43
- VIII. Technical Data 46
- (1000 ‰ = 50 mNm) 47
- Rheometer 51
- B.3 SettingtheGap 55
Relacionado con productos y manuales para Instrumentos de medición Brookfield R/S CPS Rheometer
(9 paginas)Allied Telesis Switch AT-9000/12POE manuals
Owner’s manuals and user’s guides for Network switches Allied Telesis Switch AT-9000/12POE.
We providing 1 pdf manuals Allied Telesis Switch AT-9000/12POE for download free by document types: User Manual
Comentarios a estos manuales