Brookfield DV-III Ultra Rheometer Manual de usuario Pagina 15
- Pagina / 133
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Brookeld Engineering Laboratories, Inc. Page 15 Manual No. M/98-211-B0104
Brookeld Engineering Laboratories, Inc. Page 15 Manual No. M98-211-E0912
I.11 Connections
The DV-III Ultra Rheometer is capable of communicating with several external devices to enhance
operation. The cables and connections required for proper communication are detailed below.
S
RHEOLOADER
The DVP-202 USB Cable is used to connect the USB Port on the DV-III Ultra Base to the computer.
The DVP-80 cable is used to connect the RS-232 serial port on the DV-III Ultra base to Com Port
1 or Com Port 2 on the computer. Some PCs may also have Com Port 3 and Com Port 4. These
cables are supplied with the DV-III Ultra.
S
RHEOLOADER AND EZ-YIELD SOFTWARE
The DVP-80 cable is used to connect the RS-232 serial port on the DV-III Ultra base to Com Port
1 or Com Port 2 on the computer. Some PCs may also have Com Port 3 and Com Port 4. This
cable is supplied with the DV-III Ultra.
S
RHEOCALC SOFTWARE
The DVP-202 USB Cable is used to connect the USB Port on the DV-III Ultra Base to the computer.
The DVP-80 cable is used to connect the RS-232 serial port on the DV-III Ultra base to Com Port
1 or Com Port 2 on the computer. Both cables are supplied with the RHEOCALC software.
S
PARALLEL PRINTER
The CAP-86 cable is used to connect the 25-pin parallel port on the DV-III Ultra base with the
Centronics port on the printer.
S
SERIAL PRINTER
The DVP-81 cable is used to connect the 9-pin serial port on the DV-III Ultra with the 25-pin serial
port on a printer.
S
THERMOSEL CONTROLLER AND TC SERIES TEMPERATURE BATHS
Earlier model baths with programmable Brookeld Controllers will also work.
The DVP-141 cable is used to connect the serial port on the DV-III Ultra base to the serial port on
the controller. This cable is supplied with the controller/bath.
Be sure that the controller temperature probe is properly located in the control device (Thermosel
or bath) and connected to the controller.
Note: 1. The controller may alternately communicate with Rheocalc V.2.0 or
higher software. In this conguration, the controller is connected to the
computer through either Com Port 1 or Com Port 2 by using the DVP-80
cable. The DV-III Ultra can also be connected to a computer through
the USB Port by using the DVP-202 cable.
2. The controller must also be connected to the control device (Thermosel
or bath) with the appropriate load cable.
- BROOKFIELD DV-III ULTRA 1
- Table of Contents 3
- I. INTRODUCTION 5
- Maximum Torque Value 6
- Component Part Number 7
- Ball Bearing Option: 10
- Electrical Certication: 10
- CLAMP ASSEMBLY 12
- DV-III Ultra 12
- HEAD UNIT 12
- TENSION SCREW 12
- Connector 14
- RS-232 Serial 14
- Printer/Computer 14
- STRIP CHART RECORDER 16
- II. GETTING STARTED 18
- “REMOVE SPINDLE, LEVEL 18
- KEY.” Press a key 18
- TORQUE LESS THAN 0% 21
- SELECT SPDL key. The DV-III 21
- MOTOR ON/OFF/ESCAPE key 21
- one minute. 150 seconds 32
- USE SET:_ 33
- STEP TIME = 00:05 33
- USING PREPROGRAMMED SPEEDS 37
- OPTION/TAB key 38
- LOCKOUT OPTIONS 38
- PROG RUN key is pressed 40
- PROG RUN 40
- ENTER key. Assume that the 41
- ENTER key, our display will 41
- PROGRAMMED SPEED STOP 41
- PROGRAMMED SPEED HOLD 42
- SINGLE SPEED 49
- DVIII SPEED/TIME PAIRS 50
- B.E.V.I.S. PROGRAMS 50
- STANDARD CASSON PRINTOUT 51
- 1. Casson (Standard) 52
- 3. Bingham Plastic 52
- 4. Power Law 53
- 5. IPC Paste Analysis 53
- Figure IV-44: Test Screen 55
- Figure IV-45: Run/Data Screen 55
- Figure IV-46: Setup Screen 56
- Figure IV-47: Analysis Screen 56
- Figure IV-48 57
- = shear stress 58
- Figure IV-65 79
- V. OPTIONS 89
- ENTER key 89
- V.4 Set Temperature 91
- V.6 Timed Data Collection 93
- Do Not hit the 96
- CONE with the CUP! 96
- A.3 SETTING THE GAP 97
- Universal Spindle Ranges 99
- Rheometer at 45 RPM 100
- Spindle Speed = 45 RPM 100
- RHEOLOGICAL PROPERTIES 105
- Table D-1 (continued) 108
- (S x T) 112
- +/-) 0.1°C 114
- °C, are shown in Table E-1 114
- Table E-1 115
- °C, 93.3°C, 149°C 115
- Table E-2 115
- + 500) cP = (+/-) 622.57 cP 119
- Figure F-1 121
- DV-III Ultra Stand Assembly 122
- Item Part # Description Qty 122
- 4 hex digits. Calculate the 125
- Zero offset = tval/100 125
- VISCOSITY TEST REPORT 133
Relacionado con productos y manuales para Instrumentos de medición Brookfield DV-III Ultra Rheometer
(83 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales